As we start to gain on the summer (or we move from the warm summer months to the much cooler winter months south of the Equator), it’s time to start thinking about climate control in our shops. Today, let us know whether you have a totally tricked-out full-on AC/heat setup or you rely on nature to create your ambient shop temperature.

Similar Posts:

• Tools I use: my new shop heater
• A moving experience
• Now, that’s hot!
• Tools I use: My sanders
• Woodworking Spotlight: Roe Terry
• Four More Years
• The only labor I’m doing today…

But, there are some woodworkers out there who aren’t alone. No, I’m not talking about disembodied spirits or anything like that. I’m talking about those companions of the four-legged variety. A shop cat or dog can help make the time a little bit more fun (or frustrating, based on the pet’s personality) and can even provide a sounding board for design decisions. “So, Fluffy, what do you think about dovetails here?”

This week, tell us if you have a shop mascot and what the experience is like for you.

Similar Posts:

• Which pro do you know?
• Tools I use – My Keller Dovetail Jig
• The Halfway Point
• Room to Dream
• I wish I would have held off…
• Doing the poll dance
• A woodworking funny…

I know, you have heard EVERYTHING about shop safety, right?  You’ve heard it all, seen it all, tried it all and you can’t stand to see something else about it.  Sure. But, it never hurts to have a refresher to help remind you about how to prevent painful, disfiguring and costly injuries.

While all tools pose a potential safety risk, the table saw remains the number one culprit in shop injuries. Accidental blade contact and kickback are two of the common ways that people can be injured.

Of course, there are a number of safety devices included in your table saw.  Whether it’s flesh-sensing technology or a simple splitter and blade guard, each of these gadgets works to help prevent mishaps. While they are useful, some woodworkers see them as non-essential add ons that just slow them down.

This week, look at your table saw setup and let us know how much safety equipment you use on your table saw. Is it the whole shebang, or do you get rid of those safety devices?

Similar Posts:

• Woodworker’s Safety Week – Power tool safety
• The most important safety device
• Safety is job number… what?
• Offput by off cuts?
• A time to stop and think
• Woodworker’s Safety Week – Eye and Face protection
• How big do you want it?

From simple shop-made tools to fancy, elaborate highly-engineered cast iron behemoths, there is a work holding contraption that can immobilize your work for just about every taste, preference and price point.

This week, we’re looking to see how many vises are on the main workbench in your shop. Do you have a vise in every corner of your bench, or do you rely on other work holding devices?

Similar Posts:

• Shop Q&A – Face Vise Location
• Pair-a-vise(s) Under Workshop Lights
• Get a Grip
• Q&A About tail vises
• Woodworking Spotlight: Lake Erie Toolworks
• In Love With Ugly
• Trust in the Wedgie

While they may have started as essential machinist’s tools, drill presses have become a workshop staple. Hey, if you need a hole bored straight into a piece of wood, there’s no more accurate way to get the job done. Drill presses also have scores of other uses. Want to bore holes on an angle into a piece of wood? Set the table angle and bore away. Chuck a sanding sleeve in there and you have a spindle sander. You can get a mortising attachment to make it a multi-tasker.

But, then there are the drill presses that sit for a long time collecting dust. I know someone who has no fewer than six drill presses, because other woodworkers give him theirs when they discover they don’t get any use.

Today’s question – just how essential are drill presses in a woodworking shop?  Critical pieces of machinery, or a total waste of time?

 
Similar Posts:

• The busted chair… y’all are good!
• A boring conversation
• Are we there yet?
• Tools I use: my circle cutter
• Who was that masked man?
• A collection connection
• It’s hip to be square

Pastry chefs will classify ingredients as wet goods or dry goods, and it’s not as easy as it seems. Sugar is considered to be a wet ingredient.

When it comes to woodworkers, we also tend to classify ourselves into categories based on our abilities and knowledge of the craft.

This week, I’m looking to see how you classify yourself as a woodworker at this moment.  Don’t be bashful – be as honest as possible.  Remember, no one has to know you you voted.

Well, you’ll know….

Similar Posts:

• Become your own mixologist
• Doing the poll dance
• Is it failure… or opportunity?
• Which pro do you know?
• Short and useful
• Finding those roots
• “You are tough to buy for…”

But, there’s a show that doesn’t normally get a lot of discussion -the American Woodshop.

It’s a glaring omission, considering that the show has been on the air for 19 seasons, and host Scott Phillips has been an institution on the show. He’s been out there at woodworking shows, demonstrating tools. Over the years, viewers have watched him build a shop and turn out some sweet looking projects.

But, there has also been a number of woodworkers who call his work amateurish and question why he has been on television for as long as he has.

Today, tell us what you think about Scott Phillips and the American Woodshop.

 
Similar Posts:

• Going to the big show
• For your viewing pleasure…
• Get Woodworking Week: Saturday
• Meet daddy’s nemesis …
• Woodworking Spotlight: Jim Heavey
• Finding those roots
• “…Who will pick up the flag?”

Wood Magazine's Bob Wilson hanging a speaker in his shop (photo courtesy Wood Magazine)

Since it’s very unlikely that you will be continuously running your table saw or router for hours on end, most woodworkers are easily able to focus on those particular cuts for the necessary time and then listen to something else between operations.  And, when it comes to a tedious task like sanding, well, a radio is very much appreciated.

This week, we want to know what you listen to while in the shop.  Sure, you may listen to several different things, but which is the primary thing you will listen to?

Similar Posts:

• Woodworking Spotlight: Matt Vanderlist
• Tools I use: my table saw
• Are you ready for some football?
• Doing the poll dance
• Woodworking Spotlight: Mike Siemsen
• Shop short cuts
• It starts with the word fun…

Yesterday, while I was at the Woodworking Show in Tampa, I saw some folks hugging the wall just taking some mental notes on what they wanted to buy, while others were staggering out the doors of the convention hall, struggling to carry home all of their goodies.

This week, we want to know how you feel about purchasing something – anything – at a woodworking show or expo.

Similar Posts:

• Expo-sing myself to new stuff
• Come one… come all!
• Stuff I’ve Built: The corner entertainment unit
• Going to the big show
• The most powerful tool in your shop
• My day at the Woodworking Show
• Stuff I’ve built: The hanging wall cabinet

Of course, GETTING that wood to your shop can pose a challenge. I’m discovering that with gas prices very high these days, my smaller, more economical car makes sense for the daily commute, but it totally stinks at carrying wood home from the hardwood dealer.

Today, let us know how you get wood to your shop.

 
Similar Posts:

• The most powerful tool in your shop
• Buying lumber: The hardwood supplier
• More monkey business
• The Halfway Point
• Woodworking Spotlight: Andrew Lunn
• An unexpected family project
• Species Spotlight: Olivewood